HARDWARE

Würth magnetic bit holder for drills and impact drivers. The magnet holds the screw on the bit, so you can place a screw-on with one hand while the other holds the wall. Takes our Torx T20 and T25 bits.

Würth Torx T20 bit, 120 mm long, made to drive our T20 wood screws into screw-on holds and volumes. The 120 mm length reaches screws set deep in a volume or a big screw-on. Fits any drill or impact driver, or our magnetic bit holder.

Matching screws: Wood Screws.

Würth Torx T25 bit, 120 mm long, made to drive our T25 wood screws into screw-on holds and volumes. The 120 mm length reaches screws set deep in a volume or a big screw-on. Fits any drill or impact driver, or our magnetic bit holder.

Matching screws: Wood Screws.

Würth Torx T20 bit, 70 mm long, made to drive our T20 wood screws into screw-on holds and volumes. The compact 70 mm length keeps the drill close to the hold for precise setting. Fits any drill or impact driver, or our magnetic bit holder.

Matching screws: Wood Screws.

Würth Torx T25 bit, 70 mm long, made to drive our T25 wood screws into screw-on holds and volumes. The compact 70 mm length keeps the drill close to the hold for precise setting. Fits any drill or impact driver, or our magnetic bit holder.

Matching screws: Wood Screws.

8 mm T-handle hex key with three drive ends, sized for the M10 socket head bolts used on climbing holds. Use the long end to spin the bolt in fast, then the T-handle for the final tightening torque.

M10 machine tap for cleaning out and re-threading T-nuts on climbing walls. A crossed or clogged T-nut gets back into service in seconds, without opening the panel. Mounts on a drill for speed.

M10 hand tap with a Würth ratchet tap holder, to re-thread damaged T-nuts on your climbing wall by hand. The ratchet works in tight spots, under a roof or behind a volume, with full control on the thread.

Klimas 5 x 120 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T25 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 120 mm
• Torx T25 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• Box of 200 screws

Use a T25 bit: the wrong size slips and chews the head. Our T25 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Klimas 5 x 70 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T25 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 70 mm
• Torx T25 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• Box of 200 screws

Use a T25 bit: the wrong size slips and chews the head. Our T25 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Klimas 5 x 50 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T25 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 50 mm
• Torx T25 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• Box of 300 screws

Use a T25 bit: the wrong size slips and chews the head. Our T25 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Klimas 5 x 90 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T25 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 90 mm
• Torx T25 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• Box of 200 screws

Use a T25 bit: the wrong size slips and chews the head. Our T25 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth ASSY 4 5 x 120 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T20 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 120 mm
• Torx T20 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• CE marked, ETA approved
• Box of 100 screws

Use a T20 bit: the wrong size slips and chews the head. Our T20 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Klimas 5 x 40 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T25 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 40 mm
• Torx T25 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• Box of 500 screws

Use a T25 bit: the wrong size slips and chews the head. Our T25 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth ASSY 4 5 x 70 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T20 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 70 mm
• Torx T20 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• CE marked, ETA approved
• Box of 200 screws

Use a T20 bit: the wrong size slips and chews the head. Our T20 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth ASSY 4 5 x 50 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T20 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 50 mm
• Torx T20 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• CE marked, ETA approved
• Box of 250 screws

Use a T20 bit: the wrong size slips and chews the head. Our T20 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth ASSY 4 5 x 90 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T20 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 90 mm
• Torx T20 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• CE marked, ETA approved
• Box of 100 screws

Use a T20 bit: the wrong size slips and chews the head. Our T20 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth ASSY 4 5 x 40 mm wood screws for fixing screw-on holds, feet and volumes to plywood climbing walls. Torx T20 drive for a clean, cam-out-free set.

• Diameter 5 mm, length 40 mm
• Torx T20 drive
• Countersunk head, sits flush in the hold
• Zinc-plated steel
• CE marked, ETA approved
• Box of 500 screws

Use a T20 bit: the wrong size slips and chews the head. Our T20 bits and magnetic bit holder are in Tools. For bolt-on holds, see M10 Bolts.

Würth M10 x 120 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 120 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 100 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 100 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 90 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 90 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 70 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 70 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 80 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 80 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 50 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 50 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 60 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 60 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.

Würth M10 x 40 mm socket head cap screws for fixing climbing holds into M10 T-nuts. The standard bolt on every climbing wall, from commercial gyms to home walls.

• Thread: M10, length 40 mm
• Standard: ISO 4762 (formerly DIN 912)
• Strength class: 8.8
• Steel, blue zinc plated
• Drive: 8 mm hex socket

Choosing the length: the bolt goes through the hold and must engage the full depth of the T-nut. Too short, it won't hold. Tighten with our 8 mm T-handle hex key, in Tools.